Search results

  1. 0

    Need some brake:abs help

    Ok I’ll give an update here. I tried again multiple times today. I tried the Teflon tape around the bleeder screws. No dic. I thought maybe by changing the fluid I sucked debris through the brake system. I completely drained everything and tried compressed air through all the lines. Still no...
  2. 0

    Need some brake:abs help

    I know what your talking about with the soft pedal. How ever I know this is different. As my gage is the rear calipers have not pushed out the pistons to squeeze on the rotor as it still slops around.
  3. 0

    Need some brake:abs help

    Thanks. I will try the Teflon tape, I did try pumping the brakes as well but did not seem to expel any more fluid. I also tried bleeding the brakes brakes the normal way. Back right, back left, front right and front left. It’s still got a soft pedal.
  4. 0

    Need some brake:abs help

    To be honest I wish I was that stupid. Lol bleed screws are the highest point on caliper compared to the flex hose.
  5. 0

    Need some brake:abs help

    To be honest I wish I was that stupid. Lol bleed screws are the highest point on caliper compared to the flex hose.
  6. 0

    Need some brake:abs help

    Hey gents. Need some help. I just replaced both rear calipers. I used a vacuum pump to pull fresh brake fluid through the system on both sides. How ever with doing this it seems that the petal is soft. No matter how many times bleeding the brakes. It also seems like there is no fluid going to...
  7. 0

    Caliper slide pins

    So you are correct from what I have found the bushing goes to the bottom. I don’t know if I am high as a kite or what but I tried the bushing in both top and bottom hole and it seemed to fit better in the bottom hole. On both front brakes. Atleast lol
  8. 0

    Caliper slide pins

    That’s interesting. The pin feels super loose in there with no bushing.
  9. 0

    Caliper slide pins

    So if I am reading this correct it will be always the top position on both sides?
  10. 0

    Caliper slide pins

    Everything I can find only shows one https://www.carid.com/acdelco/gm-original-equipment-front-disc-brake-caliper-guide-pin-kit-mpn-88965686.html?singleid=2980208900&url=11298860
  11. 0

    Caliper slide pins

    Hey guys I just re did my brakes. One slide pin has a bushing and the other is just a straight pin. Do it matter in which spot either goes?
  12. 0

    Exhaust

    Hey guys my flex pipe and muffler is shot. are there any cat back systems that are quiet. or are there any factory replacements?
  13. 0

    P0014

    Thanks for the heads up guys. I bought the part have not put it in or changed the oil yet. But it only did it for 2 days and now is gone. I pulled the connector and the plug is dry. I don’t know if i just replace it because I have it or leave it out till it acts up again.
  14. 0

    P0014

    Hey gents, The last few times starting my truck when cold After sitting for a little bit the idle goes crazy. High low high low almost stalling then clears up. Check engine light comes on with the P0014 code cam position exhaust side b I believe. I have done some research and it seems one of...
  15. 0

    Fuel lines

    Is the evap line the top line or bottom lone
  16. 0

    Fuel lines

    So I guess the other line may be a vapour line? There should be no fuel in that vapour line?
  17. 0

    Fuel lines

    Sorry my bad it’s a 2007 slt with the 4.2l. Lately I have been smelling fuel. Now after the truck sits for a couple hours it loses its prime. The truck has A puddle of fuel under the drivers door. So I climbed under the truck today and right above the transfer case where the plastic line meets...
  18. 0

    Fuel lines

    Hey have any of you guys ever replaced the steel fuel lines? Are there a direct replacement for them?
  19. 0

    hp tuners

    so really there is not a lot of guys here that tune their own stuff. you go on the full size sites and everyone is a professional tuner. lol I started with deleting the torque management as that is pretty standard between all the gm vehicles. what is a good rpm to bring the pe in at. I believe...
  20. 0

    hp tuners

    hey is there any guys out there that are using hp tuners on their 4.2l or are you guys just having a shop tune your ecus for you?
  21. 0

    possible 4x4 issue

    also no I have not read any tutorials kinda of new to site. is there anything I should be looking at or doing to make this less of an issue
  22. 0

    possible 4x4 issue

    hey thanks guys. the vehicle just turned 230 000 km . the diff oil has been changed in the last 15000. it looked brand new and the tranny and transfer case was done about 30000k ago. I did let the tires rotate really slow as soon as the brake was let off the two back tires slowly started to...
  23. 0

    possible 4x4 issue

    hey guys, I got a question about my 4x4 and possible issue. I have a 2007 envoy slt i6. today I was backing my sled trailer in at my brothers on the grass. which was wet and really greasy. I tried to put my truck in 4 low. I used neutral, let the light stop flashing. I then put it in reverse and...
  24. 0

    tire size question

    hey guys I need some new rubber for my envoy. first of I will say my summer tires are 265/35/22 and my winter rims are 245/65/18s. to me the 18s are a crap size rim to look for decent price and sized tires. I am looking at the hankook dynapro atm as I know they are a grate tire. but the only...
  25. 0

    kill switch/ anti theft

    hey guys i am looking to add a kill switch to my envoy. i just added some new rims and i dont need my truck to go missing. so i was wondering where is the best place to wire in a toggle switch so it cant be started. i know some guys say to wire it into the yellow wire under the dash or to wire...
  26. 0

    changed my bags for springs and couple questions

    Thanks I just ordered from my dealer. I thought there was one for bottom too but guess not
  27. 0

    changed my bags for springs and couple questions

    ok so i was finaly sick of my leaky air bags. and it was time to upgrade / repair the 8.0 rear end to the 8.6. so i had the springs and put them in as well since the axle was out. now my only question is there suppose to be a isolator that is suppose to go between the top mount and the spring...
  28. 0

    Couple drivetrain and suspension questions

    My mission is to have a vehicle that doesn't drop to the bump stops and set off my alarm. I want something that is fairly smooth riding and can take a little to weight as I do pull a sea doo and sometimes snowmobile trailer in the winter. What I mean by better quailty I know springs mave a...
  29. 0

    Couple drivetrain and suspension questions

    hey thanks for those numbers. my final questions is there any better rear spring then the other. oem, moog, bilstiens, strutmaster etc and my final question is with the rear end out of the ext are the calipers and rotors the same size as the ones on my 8.0 rear end?
  30. 0

    Couple drivetrain and suspension questions

    Hey is there any chance you have write up on the install or part numbers for everything you have used and needed

Members Online

No members online now.